PM to RM

[Paul Edwards]

I recently "found out" (ie is it true?) that
there is apparently a BIOS call to go from
PM16 to RM16 on an 80286.

It originally did that via the convoluted
and slow keyboard thing. In principle I have
no problem with that, and I also have no
problem with replacing the BIOS ROM with an
updated version that uses a more efficient
(and documented in section 9.6.2 of the
"80286 and 80287 Programmer's Reference Manual")
triple fault mechanism:

https://bitsavers.org/components/intel/80286/210498-005_80286_and_80287_Programmers_Reference_Manual_1987.pdf

I also don't mind the BIOS ROM being updated
with the LOADALL instruction which has been
belatedly documented (I believe that's the
fastest solution).

So speed doesn't bother me.

But it occurs to me. If there is a BIOS interrupt
to go from PM16 to RM16, why not have one to go
from PM32 to RM16 too? As that is what I need in
PDOS/386. I rolled my own. I wasn't aware that
there might be a BIOS function to do that.

So maybe in PDOS/286 at least I can use the
official BIOS routines, assuming they exist
and I can find them and I'm not misunderstanding
something.

BFN. Paul.

[wolfgang kern]

Post by Paul Edwards
I recently "found out" (ie is it true?) that
there is apparently a BIOS call to go from
PM16 to RM16 on an 80286.
It originally did that via the convoluted
and slow keyboard thing. In principle I have
no problem with that, and I also have no
problem with replacing the BIOS ROM with an
updated version that uses a more efficient
(and documented in section 9.6.2 of the
"80286 and 80287 Programmer's Reference Manual")
https://bitsavers.org/components/intel/80286/210498-005_80286_and_80287_Programmers_Reference_Manual_1987.pdf
I also don't mind the BIOS ROM being updated
with the LOADALL instruction which has been
belatedly documented (I believe that's the
fastest solution).

I'd forget about LOADALL it's opcode has a new meaning now.
and return from protected mode needed a forced crash on 286.

Post by Paul Edwards
So speed doesn't bother me.
But it occurs to me. If there is a BIOS interrupt
to go from PM16 to RM16, why not have one to go
from PM32 to RM16 too? As that is what I need in
PDOS/386. I rolled my own. I wasn't aware that
there might be a BIOS function to do that.
So maybe in PDOS/286 at least I can use the
official BIOS routines, assuming they exist
and I can find them and I'm not misunderstanding
something.

why bother with BIOS calls (which may not be present at all)?
my "all-mode switches"
[from any to any of RM16,PM16,PM32,LM64,CM16,CM32]
are just a few bytes large and share only one system-stack,
all whats required is proper setup of GDT and IDT entries up front.
__
wolfgang

[Paul Edwards]

Post by wolfgang kern
I'd forget about LOADALL it's opcode has a new meaning now.
and return from protected mode needed a forced crash on 286.

Sure. All to be hidden behind a BIOS call.
And on a non-286 it can be done in a more
elegant way.

Post by wolfgang kern
why bother with BIOS calls (which may not be present at all)?
my "all-mode switches"
[from any to any of RM16,PM16,PM32,LM64,CM16,CM32]
are just a few bytes large and share only one system-stack,
all whats required is proper setup of GDT and IDT entries up front.

That's a good idea actually.

BFN. Paul.